Related Topics

‣  What can be the causes of damage to PVC cables and paper insulated cables?‣  What precaution should be taken while taken a cable through trenches in the following locations (a) Road crossing, (b) Railway crossing & (c) Crossing of water mains ?‣  What is called “Barrier joint” of cable ?‣  What is called “Heat shrinkable joint” of cable?‣  What are the procedures to be adopted for determining the types of cable faults ?‣  What is proximity effect ?‣  What is soil thermal resistivity ?‣  What are the methods of cable laying ?‣  what special cares are to be taken for storage of cable drum ?‣  What are the load conditions of an underground cable ?‣  What do you mean by thermal resistance of a single core cable ?‣  What do you mean by the term “Dielectric losses” ?‣  What is the procedure of reducing the sheath losses in sheaths of the three single core cables in a 3-phase system ?‣  What do you mean by the term “Sheath losses” ?‣  What do you mean by MIND cable and where is it used ?‣  What do you mean by XLPE cable and what are its advantages over conventional cables ?‣  What are varnished cambric insulated cables ?‣  Interview Question of Underground Cable

Index

SymbolsTransformerRelayPower-SystemBasic-electricalACSR-ConductorCircuit-BreakerInterview-questions-of-Basic-ElectricityInterview-questions-of-transformerInsulatorCurrent-TransformerMCQMCQ-powersystemThermal-power-stationInterview-questions-of-Power-SystemPower-ElectronicsInterview-questions-of-Underground-CableInterview-questions-of-IlluminationIlluminationMCQ-of-ElectronicsMCQ-of-Basic-ElectricalMCQ-of-Transformers MCQ-of-D.C-motor MCQ-of-D.C-generatorsMCQ-Control-SystemMCQ-Measurementsmcq-of-Generation-power-systemMCQ-of-Induction-MotorMCQ-of-Transmission-Distribution

What are the methods of cable laying ?

There are five different methods of laying cables e.g. (a) Laying direct in ground, (b) Drawing in ducts, (c) Laying on racks in air, (d) Laying on racks inside a cable tunnel and (e) Laying along buildings or structures.


what are the applications of different systems of cable laying?

Direct laying is applied in open soil. Draw in the system is applied in congested areas and for underground railway crossing etc. were frequent excavation is inconvenient. The solid system is not used is not used nowadays. Laying on brackets, racks and clears is used inside the building, factories, substation, power station & tunnels etc.

Related topics :



Recent Post

Multiple Choice Question (MCQ) of Electronics page-17:
241. Which of the following statement is true? a) The saturation voltage VCF of silicon transistor is more than germanium transistor.
b) The saturation voltage VCE for germanium transistor is more than silicon transistor.
c) The saturation voltage VCE for silicon transistor is same as that for germanium.
d) The saturation voltage VCE for silicon transistor is lower than germanium transistor.

Read more...

Multiple Choice Question (MCQ) of Electronics page-16:
226. Which of the following statement is correct? a) Inner electrons are always present in the semiconductor.
b) Bound electrons are always present in the semiconductor.
c) Free electrons are always present in the semiconductor.
d) Inner and bound electrons are always present in the semiconductor.

Read more...

Multiple Choice Question (MCQ) of Electronics page-15:
211. The materials whose electrical conductivity is usually less than 1 × 106 mho/m are a) Semiconductors
b) Conductors
c) Insulators
d) Alloys

Read more...

Multiple Choice Question (MCQ) of Electronics page-14:
196. In which of the following device the base resistors are not added in the package but added externally? a) UJT
b) CUJT
c) PUT
d) None of the above

Read more...

Multiple Choice Question (MCQ) of Electronics page-13:
181. The conduction in JEFT is always by the a) Majority carriers
b) Minority carriers
c) Holes
d) Electrons
e) Holes and electrons simultaneously

Read more...